Semaphores¶
A semaphore is a kernel object that implements a traditional counting semaphore.
Concepts¶
Any number of semaphores can be defined (limited only by available RAM). Each semaphore is referenced by its memory address.
A semaphore has the following key properties:
A count that indicates the number of times the semaphore can be taken. A count of zero indicates that the semaphore is unavailable.
A limit that indicates the maximum value the semaphore’s count can reach.
A semaphore must be initialized before it can be used. Its count must be set to a non-negative value that is less than or equal to its limit.
A semaphore may be given by a thread or an ISR. Giving the semaphore increments its count, unless the count is already equal to the limit.
A semaphore may be taken by a thread. Taking the semaphore decrements its count, unless the semaphore is unavailable (i.e. at zero). When a semaphore is unavailable a thread may choose to wait for it to be given. Any number of threads may wait on an unavailable semaphore simultaneously. When the semaphore is given, it is taken by the highest priority thread that has waited longest.
Note
The kernel does allow an ISR to take a semaphore, however the ISR must not attempt to wait if the semaphore is unavailable.
Implementation¶
Defining a Semaphore¶
A semaphore is defined using a variable of type k_sem.
It must then be initialized by calling k_sem_init().
The following code defines a semaphore, then configures it as a binary semaphore by setting its count to 0 and its limit to 1.
struct k_sem my_sem;
k_sem_init(&my_sem, 0, 1);
Alternatively, a semaphore can be defined and initialized at compile time
by calling K_SEM_DEFINE.
The following code has the same effect as the code segment above.
K_SEM_DEFINE(my_sem, 0, 1);
Giving a Semaphore¶
A semaphore is given by calling k_sem_give().
The following code builds on the example above, and gives the semaphore to indicate that a unit of data is available for processing by a consumer thread.
void input_data_interrupt_handler(void *arg)
{
/* notify thread that data is available */
k_sem_give(&my_sem);
...
}
Taking a Semaphore¶
A semaphore is taken by calling k_sem_take().
The following code builds on the example above, and waits up to 50 milliseconds for the semaphore to be given. A warning is issued if the semaphore is not obtained in time.
void consumer_thread(void)
{
...
if (k_sem_take(&my_sem, K_MSEC(50)) != 0) {
printk("Input data not available!");
} else {
/* fetch available data */
...
}
...
}
Suggested Uses¶
Use a semaphore to control access to a set of resources by multiple threads.
Use a semaphore to synchronize processing between a producing and consuming threads or ISRs.
API Reference¶
-
group
semaphore_apis Defines
-
K_SEM_MAX_LIMIT¶ Maximum limit value allowed for a semaphore.
This is intended for use when a semaphore does not have an explicit maximum limit, and instead is just used for counting purposes.
-
K_SEM_DEFINE(name, initial_count, count_limit)¶ Statically define and initialize a semaphore.
The semaphore can be accessed outside the module where it is defined using:
extern struct k_sem <name>;
- Parameters
name – Name of the semaphore.
initial_count – Initial semaphore count.
count_limit – Maximum permitted semaphore count.
Functions
-
int
k_sem_init(struct k_sem *sem, unsigned int initial_count, unsigned int limit)¶ Initialize a semaphore.
This routine initializes a semaphore object, prior to its first use.
See also
- Parameters
sem – Address of the semaphore.
initial_count – Initial semaphore count.
limit – Maximum permitted semaphore count.
- Returns
0 – Semaphore created successfully
-EINVAL – Invalid values
-
int
k_sem_take(struct k_sem *sem, k_timeout_t timeout)¶ Take a semaphore.
This routine takes sem.
- Function properties (list may not be complete)
Note
timeout must be set to K_NO_WAIT if called from ISR.
- Parameters
sem – Address of the semaphore.
timeout – Waiting period to take the semaphore, or one of the special values K_NO_WAIT and K_FOREVER.
- Returns
0 – Semaphore taken.
-EBUSY – Returned without waiting.
-EAGAIN – Waiting period timed out, or the semaphore was reset during the waiting period.
-
void
k_sem_give(struct k_sem *sem)¶ Give a semaphore.
This routine gives sem, unless the semaphore is already at its maximum permitted count.
- Function properties (list may not be complete)
- Parameters
sem – Address of the semaphore.
- Returns
N/A
-
void
k_sem_reset(struct k_sem *sem)¶ Resets a semaphore’s count to zero.
This routine sets the count of sem to zero. Any outstanding semaphore takes will be aborted with -EAGAIN.
- Parameters
sem – Address of the semaphore.
- Returns
N/A
-
unsigned int
k_sem_count_get(struct k_sem *sem)¶ Get a semaphore’s count.
This routine returns the current count of sem.
- Parameters
sem – Address of the semaphore.
- Returns
Current semaphore count.
-
User Mode Semaphore API Reference¶
The sys_sem exists in user memory working as counter semaphore for user mode thread when user mode enabled. When user mode isn’t enabled, sys_sem behaves like k_sem.
-
group
user_semaphore_apis Defines
-
SYS_SEM_DEFINE(_name, _initial_count, _count_limit)¶ Statically define and initialize a sys_sem.
The semaphore can be accessed outside the module where it is defined using:
extern struct sys_sem <name>;
Route this to memory domains using K_APP_DMEM().
- Parameters
_name – Name of the semaphore.
_initial_count – Initial semaphore count.
_count_limit – Maximum permitted semaphore count.
Functions
-
int
sys_sem_init(struct sys_sem *sem, unsigned int initial_count, unsigned int limit)¶ Initialize a semaphore.
This routine initializes a semaphore instance, prior to its first use.
- Parameters
sem – Address of the semaphore.
initial_count – Initial semaphore count.
limit – Maximum permitted semaphore count.
- Returns
0 – Initial success.
-EINVAL – Bad parameters, the value of limit should be located in (0, INT_MAX] and initial_count shouldn’t be greater than limit.
-
int
sys_sem_give(struct sys_sem *sem)¶ Give a semaphore.
This routine gives sem, unless the semaphore is already at its maximum permitted count.
- Parameters
sem – Address of the semaphore.
- Returns
0 – Semaphore given.
-EINVAL – Parameter address not recognized.
-EACCES – Caller does not have enough access.
-EAGAIN – Count reached Maximum permitted count and try again.
-
int
sys_sem_take(struct sys_sem *sem, k_timeout_t timeout)¶ Take a sys_sem.
This routine takes sem.
- Parameters
sem – Address of the sys_sem.
timeout – Waiting period to take the sys_sem, or one of the special values K_NO_WAIT and K_FOREVER.
- Returns
0 – sys_sem taken.
-EINVAL – Parameter address not recognized.
-ETIMEDOUT – Waiting period timed out.
-EACCES – Caller does not have enough access.
-
unsigned int
sys_sem_count_get(struct sys_sem *sem)¶ Get sys_sem’s value.
This routine returns the current value of sem.
- Parameters
sem – Address of the sys_sem.
- Returns
Current value of sys_sem.
-