This is the documentation for the latest (main) development branch of Zephyr. If you are looking for the documentation of previous releases, use the drop-down menu on the left and select the desired version.

solomon,ssd16xxfb (on spi bus)¶

Vendor: Solomon Systech Limited

Description¶

SSD16XX 250x150 EPD display controller

Properties¶

Properties not inherited from the base binding file.

Name	Type	Details
`height`	`int`	Height in pixel of the panel driven by the controller This property is required.
`width`	`int`	Width in pixel of the panel driven by the controller This property is required.
`pp-height-bits`	`int`	Number of bits used for the height parameters This property is required.
`pp-width-bits`	`int`	Number of bits used for the width parameters This property is required.
`gdv`	`uint8-array`	Gate driving voltage values This property is required.
`sdv`	`uint8-array`	Source driving voltage values This property is required.
`vcom`	`int`	VCOM voltage This property is required.
`border-waveform`	`int`	Border waveform This property is required.
`softstart`	`uint8-array`	Booster soft start values
`orientation-flipped`	`boolean`	Last column address is mapped to first segment
`reset-gpios`	`phandle-array`	RESET pin. The RESET pin of SSD16XX is active low. If connected directly the MCU pin should be configured as active low. This property is required.
`dc-gpios`	`phandle-array`	DC pin. The DC pin of SSD16XX is active low (transmission command byte). If connected directly the MCU pin should be configured as active low. This property is required.
`busy-gpios`	`phandle-array`	BUSY pin. The BUSY pin of SSD16XX is active high. If connected directly the MCU pin should be configured as active high. This property is required.
`lut-initial`	`uint8-array`
`lut-default`	`uint8-array`
`tssv`	`int`	Temperature Sensor Selection Value Display controller can have integrated temperature sensor or an external temperature sensor is connected to the controller. The value selects which sensor should be used.
`spi-max-frequency`	`int`	Maximum clock frequency of device's SPI interface in Hz This property is required.
`supply-gpios`	`phandle-array`	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
`vin-supply`	`phandle`	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “solomon,ssd16xxfb” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) This property is required. See Important properties for more information.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.