This is the documentation for the latest (main) development branch of Zephyr. If you are looking for the documentation of previous releases, use the drop-down menu on the left and select the desired version.

sitronix,st7735r (on spi bus)¶

Vendor: Sitronix Technology Corporation

Description¶

ST7735R 160x128 display controller

Properties¶

Properties not inherited from the base binding file.

Name	Type	Details
`reset-gpios`	`phandle-array`	RESET pin. The RESET pin of ST7735R is active low. If connected directly the MCU pin should be configured as active low. This property is required.
`cmd-data-gpios`	`phandle-array`	D/CX pin. The D/CX pin of ST7735R is active low (transmission command byte). If connected directly the MCU pin should be configured as active low. This property is required.
`height`	`int`	Height in pixels of the panel driven by the controller This property is required.
`width`	`int`	Width in pixels of the panel driven by the controller This property is required.
`x-offset`	`int`	The column offset in pixels of the LCD to the controller memory This property is required.
`y-offset`	`int`	The row offset in pixels of the LCD to the controller memory This property is required.
`madctl`	`int`	Memory Data Access Control
`colmod`	`int`	Interface Pixel Format Default value: `6`
`pwctr1`	`uint8-array`	Power Control 1 Parameter Default value: `[180, 20, 4]`
`pwctr2`	`uint8-array`	Power Control 2 Parameter Default value: `[192]`
`pwctr3`	`uint8-array`	Power Control 3 Parameter Default value: `[10, 0]`
`pwctr4`	`uint8-array`	Power Control 4 Parameter Default value: `[138, 38]`
`pwctr5`	`uint8-array`	Power Control 5 Parameter Default value: `[138, 238]`
`gamctrp1`	`uint8-array`	Positive Voltage Gamma Control Parameter This property is required.
`gamctrn1`	`uint8-array`	Negative Voltage Gamma Control Parameter This property is required.
`frmctr1`	`uint8-array`	Frame rate control (normal mode / full colors) Default value: `[5, 58, 58]`
`frmctr2`	`uint8-array`	Frame rate control (idle mode / 8 colors) Default value: `[5, 58, 58]`
`frmctr3`	`uint8-array`	Frame rate control (partial mode / full colors) Default value: `[5, 58, 58, 5, 58, 58]`
`caset`	`uint8-array`	Column Address Set Default value: `[0, 0, 0, 127]`
`raset`	`uint8-array`	Row Address Set Default value: `[0, 0, 0, 159]`
`vmctr1`	`int`	VCOM Control 1 Default value: `10`
`invctr`	`int`	Display Inversion Control Default value: `7`
`spi-max-frequency`	`int`	Maximum clock frequency of device's SPI interface in Hz This property is required.
`supply-gpios`	`phandle-array`	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
`vin-supply`	`phandle`	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “sitronix,st7735r” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) This property is required. See Important properties for more information.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.