This is the documentation for the latest (main) development branch of Zephyr. If you are looking for the documentation of previous releases, use the drop-down menu on the left and select the desired version.

sharp,ls0xx (on spi bus)¶

Vendor: Sharp Corporation

Description¶

Sharp memory display controller

Properties¶

Properties not inherited from the base binding file.

Name	Type	Details
`height`	`int`	Height in pixel of the panel driven by the controller This property is required.
`width`	`int`	Width in pixel of the panel driven by the controller This property is required.
`extcomin-gpios`	`phandle-array`	EXTCOMIN pin The EXTCOMIN pin is where a square pulse for toggling VCOM will be given
`extcomin-frequency`	`int`	EXTCOMIN pin toggle frequency The frequency with which the EXTCOMIN pin should be toggled. See datasheet of particular display. Higher frequency gives better contrast while low frequency saves power.
`disp-en-gpios`	`phandle-array`	DISPLAY pin The DISPLAY pin controls if the LCD displays memory contents or white screen. If defined, the pin will be set high during driver initialization. display blanking apis can be used to control it.
`spi-max-frequency`	`int`	Maximum clock frequency of device's SPI interface in Hz This property is required.
`supply-gpios`	`phandle-array`	GPIO specifier that controls power to the device. This property should be provided when the device has a dedicated switch that controls power to the device. The supply state is entirely the responsibility of the device driver. Contrast with vin-supply.
`vin-supply`	`phandle`	Reference to the regulator that controls power to the device. The referenced devicetree node must have a regulator compatible. This property should be provided when device power is supplied by a shared regulator. The supply state is dependent on the request status of all devices fed by the regulator. Contrast with supply-gpios. If both properties are provided then the regulator must be requested before the supply GPIOS is set to an active state, and the supply GPIOS must be set to an inactive state before releasing the regulator.

Properties inherited from the base binding file, which defines common properties that may be set on many nodes. Not all of these may apply to the “sharp,ls0xx” compatible.

Name	Type	Details
`reg`	`array`	register space This property is required. See Important properties for more information.
`label`	`string`	Human readable string describing the device (used as device_get_binding() argument) This property is required. See Important properties for more information.
`status`	`string`	indicates the operational status of a device Legal values: `'ok'`, `'okay'`, `'disabled'`, `'reserved'`, `'fail'`, `'fail-sss'` See Important properties for more information.
`compatible`	`string-array`	compatible strings This property is required. See Important properties for more information.
`reg-names`	`string-array`	name of each register space
`interrupts`	`array`	interrupts for device See Important properties for more information.
`interrupts-extended`	`compound`	extended interrupt specifier for device
`interrupt-names`	`string-array`	name of each interrupt
`interrupt-parent`	`phandle`	phandle to interrupt controller node
`clocks`	`phandle-array`	Clock gate information
`clock-names`	`string-array`	name of each clock
`#address-cells`	`int`	number of address cells in reg property
`#size-cells`	`int`	number of size cells in reg property
`dmas`	`phandle-array`	DMA channels specifiers
`dma-names`	`string-array`	Provided names of DMA channel specifiers
`io-channels`	`phandle-array`	IO channels specifiers
`io-channel-names`	`string-array`	Provided names of IO channel specifiers
`wakeup-source`	`boolean`	Property to identify that a device can be used as wake up source. When this property is provided a specific flag is set into the device that tells the system that the device is capable of wake up the system. Wake up capable devices are disabled (interruptions will not wake up the system) by default but they can be enabled at runtime if necessary.